Timedora

Area of Two-Dimensional Figures

Learn to choose area formulas for common two-dimensional figures, find missing dimensions by rearranging formulas, and calculate the area of composite shapes.

Choosing the Right Formula

What measures

tells how much flat surface a region covers. Because it measures two dimensions, its units are square units: for example, square centimeters (cm²). Before calculating, make sure the measurements use consistent units. If a formula calls for a height, that height must be perpendicular to the chosen base—not merely a slanted side.

Common area formulas
FigureArea formulaMeasurements to identify
SquareA = s²Side length s
RectangleA = lwLength l and width w
TriangleA = ½bhBase b and perpendicular height h
ParallelogramA = bhBase b and perpendicular height h
TrapezoidA = ½h(b₁ + b₂)Parallel bases b₁ and b₂; perpendicular separation h
Rhombus or kiteA = ½d₁d₂Diagonals d₁ and d₂
CircleA = πr²Radius r; if given diameter d, first use r = d/2
Regular polygonA = ½apApothem a and perimeter p
Common area formulas and the measurements each one requires.

The shape determines which measurements belong in the formula. In particular, a parallelogram’s slanted side is not its height unless it is perpendicular to the base. For a trapezoid, use the perpendicular gap between the parallel bases.

Compare a triangle and a parallelogram

A triangle and a parallelogram with the same base and have areas in the ratio 1:2. For example, with base 12 cm and height 5 cm:

Atriangle=12(12)(5)=30 cm2,Aparallelogram=(12)(5)=60 cm2.A_{\text{triangle}}=\frac12(12)(5)=30\text{ cm}^2, \qquad A_{\text{parallelogram}}=(12)(5)=60\text{ cm}^2.

The triangle’s is half the parallelogram’s because the triangle formula has the extra factor 12\frac12.

Finding a Missing

Rearrange before substituting

When the and some dimensions are known, use the appropriate formula and isolate the unknown. For a rectangle, A=lwA=lw. Dividing both sides by ll gives w=A/lw=A/l. For a triangle, A=12bhA=\frac12 bh. Multiply both sides by 2, then divide by bb, to get h=2A/bh=2A/b.

Worked example: A triangle has 42 m² and base 12 m. Solve for its height:

h=2Ab=2(42 m2)12 m=7 m.h=\frac{2A}{b}=\frac{2(42\text{ m}^2)}{12\text{ m}}=7\text{ m}.

The units make sense: divided by length leaves a length. Include the appropriate units in the result.

Check what “height” means

The height in a triangle’s formula is perpendicular to the selected base. A slanted side is not a substitute unless it is perpendicular to that base. If the is not given, it may need to be found first from other measurements; for example, the Pythagorean theorem can determine a height in a right triangle from its side lengths.

of Composite Figures

Two ways to handle a composite shape

A is made from familiar shapes. You can either add the areas of non-overlapping pieces or find the of a larger shape and subtract a cutout. First identify the shapes and any shared dimensions; an unmarked length may need to be found by adding or subtracting labeled parts.

Subtract a cutout

A 10 cm by 8 cm rectangle has a 4 cm by 3 cm rectangular corner removed. Find the whole rectangle’s , then subtract the removed part:

10(8)−4(3)=80−12=68 cm2.10(8)-4(3)=80-12=68\text{ cm}^2.

The remaining region has 68 cm². As a reasonableness check, the cutout’s (12 cm²) is less than the whole rectangle’s (80 cm²), as it must be.

Add non-overlapping pieces

For a figure made of a rectangle and a semicircle, calculate the rectangle’s lwlw and the semicircle’s 12πr2\frac12\pi r^2, then add them if the pieces do not overlap. Keep the measurements needed for each formula clear, including the semicircle’s radius.

In either strategy, make sure component areas refer to the intended parts: addition requires non-overlapping pieces, and a cutout cannot be larger than the whole figure.

  • : The process of dividing a figure into simpler parts.