Free Practice Quiz Question List

6 Integrated Switching and Wireless Practice Online Quiz Questions

Use this free practice quiz with 20 questions to review 6 Integrated Switching and Wireless Practice, test your knowledge, and prepare for your next test or exam.

20 questions

True or false

1 point

True or false: VLAN separation alone provides inter-VLAN routing and guest access control.

A
True
B
False

Choose one

1 point

You are configuring the two-link S1–S2 EtherChannel. Which statement about the LACP mode on the two switches is correct?

A
One side must use LACP active and the other must use LACP passive.
B
Both sides may use LACP active.
C
Both sides must use a static channel with LACP disabled.
D
LACP active is valid only when the member links are access ports.

Written response

1 point

In the lab VLAN plan, what purpose is assigned to VLAN 999? Enter the concise purpose.

Fill in the blank

1 point

When the two S1–S2 member links form Port-channel1, STP treats the bundle as one link.

Choose one

1 point

Which S3 port configuration matches the lab design for the AP, where management traffic is untagged and staff and guest client traffic is tagged?

A
Use access mode on VLAN 30; the AP's staff and guest traffic will be separated automatically.
B
Use trunk mode with VLAN 10 native and VLANs 20 and 30 tagged.
C
Use trunk mode with VLAN 30 native and VLANs 10 and 20 allowed for tagged client traffic.
D
Use trunk mode with VLAN 999 native and VLAN 30 omitted from the allowed list.

True or false

1 point

True or false: If clients experience a broadcast storm in the redundant switch triangle, disabling STP is an appropriate way to resolve the problem.

A
True
B
False

Written response

1 point

Which verification command from the checklist displays LACP neighbor information? Enter the command exactly as shown.

Choose all

1 point

Select all commands listed in the verification checklist that help confirm the S1–S2 EtherChannel and its LACP operation.

A
show etherchannel summary
B
show vlan brief
C
show lacp neighbor
D
show mac address-table dynamic

Fill in the blank

1 point

For each switch-to-switch trunk, the native VLAN at the two ends must .

Choose one

1 point

One VLAN works across a trunk, but another does not. Which troubleshooting action best addresses the likely causes?

A
Disable spanning tree on the trunk.
B
Check that the VLAN exists and is active, and that it is allowed on every required trunk.
C
Change the AP's management tagging, even if the affected traffic is not wireless.
D
Change the LACP mode on every switch-to-switch link.

Choose all

1 point

Select all services or settings the lab requires for end-to-end IP connectivity for a client VLAN.

A
A DHCP scope for the client VLAN.
B
A separate SSID for every physical switch port.
C
Disabling spanning tree on the client VLAN.
D
A default gateway for the client VLAN.

Open ended

1 point

A wireless client is not reaching the service it is permitted to use. Describe a layered verification sequence that would help isolate the problem, from switch connectivity through client services.

Choose one

1 point

An end-device access port configured with BPDU Guard enters an error-disabled state. What is the best next action?

A
Disable BPDU Guard and STP, then leave the port in service.
B
Assume the port is a trunk and add every VLAN to its allowed list.
C
Investigate why a BPDU or other fault occurred before restoring the edge port.
D
Configure the port as an LACP member without checking its peer.

Written response

1 point

A guest WLAN is mapped to the guest client network in the VLAN plan. Which VLAN ID should the WLAN use?

Choose one

1 point

You are setting up the three-switch topology as a small static lab, with no managed VLAN-distribution system. Which approach follows the lab guidance for making the VLANs available on the switches?

A
Configure the VLANs only on S1; the other switches will learn them automatically.
B
Configure the VLANs locally on all three switches.
C
Configure the VLANs only on switches connected to wireless clients.
D
Configure the VLANs on the AP instead of on the switches.

Choose one

1 point

A wired staff test device is being connected to an end-device port on S3. Which configuration best matches the lab’s example for that port?

A
switchport mode access; switchport access vlan 10; spanning-tree portfast; spanning-tree bpduguard enable
B
switchport mode trunk; switchport trunk allowed vlan 10,20,30,999
C
switchport mode access; switchport access vlan 20; spanning-tree portfast
D
switchport mode trunk; switchport trunk native vlan 999; spanning-tree portfast

Choose one

1 point

You plan to adapt the lab commands for a different switch model and software release before deploying them in production. What should you do first?

A
Apply the commands unchanged because Cisco IOS syntax is identical on every switch.
B
Remove all interface descriptions because they are not supported on newer platforms.
C
Check the platform documentation and adapt interface names or syntax before applying the template.
D
Disable spanning tree because platform differences make it unreliable.

Choose one

1 point

A team is adapting the lab design for a production network. What should it do with the example subnets shown in the lab?

A
Keep the example subnets; they are recommended for production because they are reserved.
B
Replace the example subnets with addressing approved for the production network.
C
Use the example subnets only for guest clients and use them unchanged for staff clients.
D
Remove subnet addressing from the design because VLANs assign addresses automatically.

True or false

1 point

True or false: The example subnets 192.0.2.0/24, 198.51.100.0/24, and 203.0.113.0/24 are reserved for documentation and lab use.

A
True
B
False

Written response

1 point

In global configuration mode, what IOS command does the lab use to create VLAN 10?

6 Integrated Switching and Wireless Practice Online Quiz Questions

Related study packs and tools