01
Choose one
1 point
An access point maps separate Staff and Guest SSIDs to different VLANs. How should its switch port generally be configured to carry traffic for both SSIDs?
Free Practice Quiz Question List
9 Integrated Network Infrastructure Labs Online Quiz Questions
Use this free practice quiz with 20 questions to review 9 Integrated Network Infrastructure Labs, test your knowledge, and prepare for your next test or exam.
20 questions
02
Choose one
1 point
A newly connected switch port has no link indicator. What is the best initial troubleshooting action?
- A
Check power, cable seating and path, termination, patch cable, and port status.
- B
Change the client’s DNS server and test again.
- C
Change the VLAN gateway address.
- D
Disable access controls on the router.
03
Choose one
1 point
A client can ping its own VLAN gateway but cannot reach a host on another subnet. Which set of checks best fits this symptom?
- A
Replace the access point because the client can reach its gateway.
- B
Change the cable tester’s wire-map setting.
- C
Check routing, subnet mask, return route, and access-control rules.
- D
Change the SSID without checking the network configuration.
04
Choose all
1 point
During final acceptance testing, which checks help establish that the network behaves according to its intended policy? Select all that apply.
- A
Verify that permitted inter-VLAN traffic works and blocked traffic remains blocked.
- B
Assume access rules work if all client devices receive IP addresses.
- C
Test DNS resolution and any required Internet access.
- D
Confirm that the management interface is reachable only from authorized locations.
05
Choose all
1 point
A wireless client associates with its SSID but has no network access. Which checks are relevant to this symptom? Select all that apply.
- A
Check the AP uplink and VLAN tagging.
- B
Check DHCP and gateway configuration.
- C
Check client isolation settings.
- D
Check authentication settings.
06
True or false
1 point
Creating separate VLANs by itself guarantees that guest clients cannot access staff or management networks.
- A
True
- B
False
07
True or false
1 point
Near electrical hazards, using a nonconductive ladder is a recommended safety practice.
- A
True
- B
False
08
Written response
1 point
What is the design called when one router link carries tagged traffic for multiple VLANs and the router uses a subinterface for each VLAN?
09
Written response
1 point
What type of tester should be used to certify that a cable installation meets applicable performance standards?
10
Fill in the blank
1 point
A VLAN separates Layer 2 domains. Communication between VLANs requires a device.
11
Fill in the blank
1 point
If a DHCP server is outside a client VLAN, configure and verify DHCP on that VLAN’s gateway.
12
Open ended
1 point
After isolating and correcting a network fault, what should the troubleshooting record include, and how should changes be tested to make the result reliable?
13
Choose one
1 point
Before connecting network equipment, what can a basic cable tester verify about a link?
- A
Check wire map and continuity before connecting equipment.
- B
Confirm the client has received the correct DNS server.
- C
Certify the cable category and performance from a basic wire-map pass.
- D
Confirm that inter-VLAN access rules are working.
14
Choose one
1 point
A basic cable tester reports a wire-map pass on a newly installed Ethernet link. What can you conclude from that result?
- A
It certifies that the cable meets its category’s performance requirements.
- B
It checks wire map and continuity, but does not certify cable category or performance.
- C
It confirms that every switch port on the link is configured correctly.
- D
It verifies that the cable can carry tagged traffic for every VLAN.
15
Written response
1 point
In the example addressing plan, which VLAN ID is designated for network management? Enter the VLAN ID.
16
Choose one
1 point
A wired staff endpoint must connect to VLAN 10 through a managed switch. How should its switch port normally be configured?
- A
Configure it as an access port in the endpoint’s intended VLAN.
- B
Configure it as a trunk carrying every VLAN on the switch.
- C
Disable VLAN membership so the endpoint can select its own VLAN.
- D
Configure it as a router subinterface.
17
True or false
1 point
True or false: Creating separate staff and guest VLANs, by itself, guarantees that guest clients cannot reach staff devices.
- A
True
- B
False
18
Written response
1 point
An access point maps multiple SSIDs to separate VLANs. What switch-port mode does its uplink generally need? Enter the switch-port mode.
19
Choose one
1 point
A DHCP server is located outside a client VLAN, and clients in that VLAN need addresses from it. What should be configured on the VLAN gateway?
- A
Configure the client switch port to obtain DNS settings from the AP.
- B
Add the server’s VLAN to the client port as a second access VLAN.
- C
Configure DHCP relay on the client VLAN’s gateway.
- D
Replace the client’s default gateway with the DHCP server’s address.
20
Choose one
1 point
In a router-on-a-stick design, which configuration allows the router to provide gateways for several VLANs over one physical link?
- A
Use an untagged router link and configure all gateways on one router interface.
- B
Assign every router subinterface the same VLAN tag.
- C
Configure VLAN tags only on the switch and leave router subinterfaces untagged.
- D
Carry tagged VLAN traffic on the router link and match each subinterface tag to its VLAN.