Timedora
Free Online Flashcard Deck

Infusion Rate Calculations Free Online Flashcards

Study Infusion Rate Calculations with 12 free online flashcards. Review key terms, definitions, and concepts with this interactive flashcard deck.

12 cards
01
Front

How do you calculate a concentration-based pump rate?

Back

Convert the dose to an amount per hour, then divide by the solution concentration to obtain
mL/hr\text{mL/hr}. For weight-based orders, include the patient’s weight and convert units as needed.

02
Front

How should you select and verify a gravity tubing drop factor?

Back

Use the drop factor printed on the specific tubing set; do not infer it from its appearance. Count drops over a full minute to verify the set gravity rate.

03
Front

What does unit cancellation check in an infusion calculation?

Back

Arrange conversion factors so unwanted units cancel, leaving the requested unit. Check that the final units match the rate being calculated.

04
Front

How do you calculate a volume-based pump setting?

Back

Divide the ordered volume in mL by the infusion time in hours. If time is in minutes, convert the rate to
mL/hr\text{mL/hr} by multiplying the volume-per-minute rate by 6060.

05
Front

What pump rate follows from 5 mcg/kg/min5\ \text{mcg/kg/min}, 70 kg70\ \text{kg}, and 400 mg/250 mL400\ \text{mg}/250\ \text{mL}?

Back

For 5 mcg/kg/min5\ \text{mcg/kg/min}, 70 kg70\ \text{kg}, and 400 mg400\ \text{mg} in 250 mL250\ \text{mL}, dimensional analysis gives 13.125 mL/hr13.125\ \text{mL/hr}. If tenths are required, the result is 13.1 mL/hr13.1\ \text{mL/hr}.

06
Front

Why use dimensional analysis in infusion calculations?

Back

It makes unit errors easier to detect by showing whether the unwanted units cancel and whether the result has the requested units.

07
Front

How do you calculate a gravity drip rate in gtt/min\text{gtt/min}?

Back

Use gtt/min=volume (mL)×drop factor (gtt/mL)time (min)\text{gtt/min}=\frac{\text{volume (mL)}\times\text{drop factor (gtt/mL)}}{\text{time (min)}}. Convert hours to minutes and report a whole number of drops per minute, following policy.

08
Front

What gravity rate delivers 750 mL750\ \text{mL} over 5 hr5\ \text{hr} using 15 gtt/mL15\ \text{gtt/mL} tubing?

Back

For 750 mL750\ \text{mL} over 5 hr5\ \text{hr} with tubing labeled 15 gtt/mL15\ \text{gtt/mL}, the rate is 37.5 gtt/min37.5\ \text{gtt/min}, approximately 38 gtt/min38\ \text{gtt/min}.

09
Front

What units should remain after a dose-based pump-rate calculation?

Back

The units cancel to mL/hr\text{mL/hr}: dose per kilogram per minute combines with patient weight, minutes per hour, unit conversion, and solution volume per drug amount.

10
Front

How should units be handled throughout an infusion calculation?

Back

Write units beside every value and arrange conversion factors so unwanted units cancel, leaving the units requested.

11
Front

What pump rate delivers 250 mL250\ \text{mL} over 90 min90\ \text{min}?

Back

For 250 mL250\ \text{mL} over 90 min90\ \text{min}, the pump rate is 250 mL90 min×60 min1 hr=166.7 mL/hr\frac{250\ \text{mL}}{90\ \text{min}}\times\frac{60\ \text{min}}{1\ \text{hr}}=166.7\ \text{mL/hr}.

12
Front

Why is a gravity infusion rate reported as whole gtt/min\text{gtt/min}?

Back

Gravity rates are expressed in whole gtt/min\text{gtt/min}, because gravity tubing is adjusted by counting drops. Follow the applicable rounding policy.