Timedora
Free Practice Quiz Question List

Stress, Strain, and Elasticity Online Quiz Questions

Use this free practice quiz with 20 questions to review Stress, Strain, and Elasticity, test your knowledge, and prepare for your next test or exam.

20 questions
01
Choose one
1 point

Which statement correctly distinguishes the proportional limit from the elastic limit on a stress–strain diagram?

  1. A

    The proportional limit and elastic limit always coincide.

  2. B

    The proportional limit marks the end of proportional stress–strain behavior, while the elastic limit marks the greatest stress from which full recovery is possible.

  3. C

    The proportional limit marks the start of necking, while the elastic limit marks fracture.

  4. D

    The elastic limit is the point where stress first becomes proportional to strain.

02
Choose all
1 point

For a prismatic bar with uniform properties that remains in the linear-elastic range, which changes would increase its axial deformation? Select all that apply.

  1. A

    Increase the axial force.

  2. B

    Increase the bar's length.

  3. C

    Decrease the cross-sectional area.

  4. D

    Decrease the elastic modulus.

  5. E

    Increase the cross-sectional area.

03
True or false
1 point

The formulas σavg=PA\sigma_{\text{avg}}=\frac{P}{A} and τavg=VA\tau_{\text{avg}}=\frac{V}{A} determine the actual normal and shear stress at every point across a cross-section.

  1. A

    True

  2. B

    False

04
Written response
1 point

Which elastic constant measures a material's resistance to uniform volume change under pressure?

05
Open ended
1 point

Explain how to calculate average normal stress and average shear stress on a cross-section. Identify the force and area terms, distinguish the directions of the two stresses, and state one limitation of the average-stress formulas.

06
Choose one
1 point

What happens when a material is loaded beyond its elastic limit?

  1. A

    The material must return fully to its original shape after unloading.

  2. B

    Permanent plastic deformation remains after unloading.

  3. C

    The stress–strain relationship must remain proportional.

  4. D

    The material has already fractured.

07
Choose all
1 point

Which statements correctly describe the directions of normal and shear stress relative to a section? Select all that apply.

  1. A

    Normal stress acts perpendicular to a section.

  2. B

    Normal stress acts tangent to a section.

  3. C

    Shear stress acts tangent to a section.

  4. D

    Shear stress acts perpendicular to a section.

08
True or false
1 point

The relationships among Young's modulus, shear modulus, Poisson's ratio, and bulk modulus stated for homogeneous, isotropic, linearly elastic materials generally apply to anisotropic materials as well.

  1. A

    True

  2. B

    False

09
Written response
1 point

What is the name of the stress–strain limit that marks the end of proportional stress–strain behavior?

10
Fill in the blank
1 point

The elastic constant that measures resistance to shear distortion is the . The elastic constant that measures resistance to uniform volume change under pressure is the .

11
Choose one
1 point

A prismatic bar has length 2 m2\,\text{m}, cross-sectional area 100 mm2100\,\text{mm}^2, and elastic modulus 200 GPa200\,\text{GPa}. It carries an axial tensile force of 10 kN10\,\text{kN} and remains in the linear-elastic range. What is its change in length?

  1. A

    0.5 mm

  2. B

    1 mm

  3. C

    2 mm

  4. D

    4 mm

12
True or false
1 point

For small shear distortions, engineering shear strain is approximately the lateral displacement divided by the distance between the sheared faces.

  1. A

    True

  2. B

    False

13
Written response
1 point

A cross-section with area 200 mm2200\,\text{mm}^2 carries an internal shear force of 12 kN12\,\text{kN}. What is the average shear stress? Enter the value in MPa.

14
Choose one
1 point

What happens when a material is loaded beyond its elastic limit?

  1. A

    The material continues to return fully to its original shape after unloading.

  2. B

    Stress remains proportional to strain at every point.

  3. C

    Permanent plastic deformation remains after unloading.

  4. D

    The material’s Young’s modulus becomes zero.

15
True or false
1 point

The proportional limit and the elastic limit always coincide.

  1. A

    True

  2. B

    False

16
Written response
1 point

A bar with original length 0.5 m0.5\,\text{m} elongates by 1 mm1\,\text{mm}. What is its engineering normal strain? Enter the dimensionless value as a decimal.

17
Choose one
1 point

A cross-section with area 300 mm2300\,\text{mm}^2 carries an internal axial tensile force of 24 kN24\,\text{kN}. What is the average normal stress?

  1. A

    8 MPa

  2. B

    24 MPa

  3. C

    80 MPa

  4. D

    800 MPa

18
Choose one
1 point

A uniform bar stretches from an original length of 200 mm200\,\text{mm} to a final length of 202 mm202\,\text{mm}. What are its engineering strain and, for uniform uniaxial deformation, its true strain? Choose the pair in that order.

  1. A

    Engineering strain =0.0100=0.0100; true strain ≈0.00995\approx0.00995

  2. B

    Engineering strain =0.00995=0.00995; true strain =0.0100=0.0100

  3. C

    Engineering strain =1.00=1.00; true strain ≈0.995\approx0.995

  4. D

    Engineering strain =2.00=2.00; true strain ≈0.0200\approx0.0200

19
Choose one
1 point

For a homogeneous, isotropic, linearly elastic material with Young’s modulus E=200 GPaE=200\,\text{GPa} and Poisson’s ratio ν=0.25\nu=0.25, what are the shear modulus GG and bulk modulus KK, respectively?

  1. A

    G=80 GPaG=80\,\text{GPa}; K≈133.3 GPaK\approx133.3\,\text{GPa}

  2. B

    G=133.3 GPaG=133.3\,\text{GPa}; K=80 GPaK=80\,\text{GPa}

  3. C

    G=100 GPaG=100\,\text{GPa}; K=66.7 GPaK=66.7\,\text{GPa}

  4. D

    G=80 GPaG=80\,\text{GPa}; K=200 GPaK=200\,\text{GPa}

20
Choose one
1 point

A cross-section has area 300 mm2300\,\text{mm}^2, internal axial force P=12 kNP=12\,\text{kN}, and internal shear force V=6 kNV=6\,\text{kN}. Using the average-stress formulas, what are the average normal stress and average shear stress, respectively?

  1. A

    σavg=40 MPa\sigma_{\text{avg}}=40\,\text{MPa}; τavg=20 MPa\tau_{\text{avg}}=20\,\text{MPa}

  2. B

    σavg=20 MPa\sigma_{\text{avg}}=20\,\text{MPa}; τavg=40 MPa\tau_{\text{avg}}=40\,\text{MPa}

  3. C

    σavg=4 MPa\sigma_{\text{avg}}=4\,\text{MPa}; τavg=2 MPa\tau_{\text{avg}}=2\,\text{MPa}

  4. D

    σavg=40 MPa\sigma_{\text{avg}}=40\,\text{MPa}; τavg=40 MPa\tau_{\text{avg}}=40\,\text{MPa}