Timedora

Bernoulli’s Equation in Fluid Flow

Understand Bernoulli’s equation as a mechanical-energy balance, its assumptions and limits, and how it explains flow speeds and pressures in common situations.

The Mechanical-Energy Balance

The Mechanical-Energy Balance

For steady flow of an incompressible fluid with negligible friction, says that mechanical energy per unit volume is conserved along a :

p+12ρv2+ρgz=constant.p + \frac{1}{2}\rho v^2 + \rho gz = \text{constant}.

At two points on the same , the sums are equal:

p1+12ρv12+ρgz1=p2+12ρv22+ρgz2.p_1 + \frac{1}{2}\rho v_1^2 + \rho gz_1 = p_2 + \frac{1}{2}\rho v_2^2 + \rho gz_2.

Here, pp is pressure, ρ\rho is density, vv is speed, zz is elevation above a chosen reference, and gg is gravitational acceleration. The terms represent pressure energy, kinetic energy, and gravitational potential energy per unit volume. Each has the units of pressure, or energy per volume: for example, ρv2\rho v^2 has units (kg/m3)(m2/s2)=J/m3(\mathrm{kg/m^3})(\mathrm{m^2/s^2})=\mathrm{J/m^3}.

Dividing through by ρg\rho g gives the form:

pρg+v22g+z=constant.\frac{p}{\rho g}+\frac{v^2}{2g}+z=\text{constant}.

Pressure, speed, and elevation need not each stay unchanged. Instead, their combined contribution stays constant: a change in one or more terms must be balanced by changes in the others. For example, in horizontal flow, elevation is unchanged, so an increase in speed accompanies a decrease in static pressure. is therefore a balance among energy forms—not a claim that each form is individually constant.

Assumptions and Limits

Assumptions and Limits

The standard Bernoulli equation is an idealized mechanical-energy balance. Apply it between points when the flow is steady (conditions at each location do not change with time), density is constant, viscous losses are negligible, and the points lie on the same . The equation also assumes there is no unaccounted energy transfer between the points—for example, work added by a pump or removed by a turbine.

Treating density as constant is a good approximation for liquids and for sufficiently low-speed gas flows. It is not appropriate in its usual incompressible form when density changes substantially, as can happen in high-speed gas flow. The condition matters too: in irrotational flow, the Bernoulli constant can be the same across streamlines, but that broader use does not follow from the standard statement alone.

Real pipe flows can lose mechanical energy through friction and fittings; pumps and turbines can add or remove it. If these effects matter, do not apply the ideal equation unchanged. Use an extended mechanical-energy equation that accounts for the relevant losses and transfers. remains useful when its assumptions are reasonable, but the assumptions—not the algebra—determine whether its predictions describe the flow.

Using

Using

A narrowing pipe

For steady , conservation of mass gives the A1v1=A2v2A_1v_1=A_2v_2. If a horizontal pipe narrows, then A2<A1A_2<A_1, so

v2=A1A2v1>v1.v_2=\frac{A_1}{A_2}v_1>v_1.

The fluid therefore moves faster in the narrower section. Apply between two sections on the same . For horizontal flow, there is no change in elevation:

p1+12ρv12=p2+12ρv22,p2=p1+12ρ(v12−v22).p_1+\frac{1}{2}\rho v_1^2=p_2+\frac{1}{2}\rho v_2^2, \qquad p_2=p_1+\frac{1}{2}\rho(v_1^2-v_2^2).

Since v2>v1v_2>v_1, the quantity in parentheses is negative, so the ideal equation predicts p2<p1p_2<p_1: static pressure is lower in the faster, narrower section. This result is useful for understanding nozzles and constrictions, though actual devices may also have significant frictional losses.

Liquid leaving a tank

For a large open tank with a small opening a vertical distance HH below the free surface, apply between the surface and the opening along the same . For steady with small losses, both points exposed to the same atmospheric pressure, and negligible surface speed, the pressure terms cancel and the opening is lower by HH. Thus,

ρgH=12ρv2⟹v=2gH.\rho gH=\frac{1}{2}\rho v^2 \quad\Longrightarrow\quad v=\sqrt{2gH}.

This is Torricelli’s result: under these ideal assumptions, the exit speed equals the speed an object would gain falling freely through height HH.

Measuring speed with a Pitot-static tube

A Pitot-static tube compares static pressure with , where the flow is brought to rest. For steady, low-speed with negligible losses, applying along the to the stagnation point gives

pstagnation−pstatic=12ρv2.p_{\text{stagnation}}-p_{\text{static}}=\frac{1}{2}\rho v^2.

Rearranging solves for speed:

v=2(pstagnation−pstatic)ρ.v=\sqrt{\frac{2(p_{\text{stagnation}}-p_{\text{static}})}{\rho}}.

Thus, measuring the pressure difference and knowing the fluid density allows the flow speed to be determined within the stated assumptions.