Timedora

Mass Conservation and Fluid Continuity

A lesson in how mass conservation becomes the continuity equation and predicts flow through pipes and storage tanks.

Balancing Mass in a

Balancing mass in a

A is a chosen region in space. Fluid can cross its boundary, called the control surface, while the amount of mass inside may change. Conservation of mass gives the balance

accumulation=∑m˙in−∑m˙out.\text{accumulation} = \sum \dot m_{\rm in} - \sum \dot m_{\rm out}.

The rate of mass accumulating inside equals the total rate entering minus the total rate leaving. Equivalently, plus net outward mass flow is zero. In the surface-integral form, the control-surface normal points outward; flow leaving therefore contributes positive net outward flow, while flow entering contributes negative net outward flow.

This balance applies to both steady and unsteady flow. For a steady flow in a fixed , mass inside does not change with time, so is zero and total inflow equals total outflow. In unsteady flow, mass inside can change, so the two flow rates need not match.

Worked example: a filling tank

For an incompressible liquid in a tank with constant horizontal area ATA_T, a rise in liquid height hh stores volume at rate AT dh/dtA_T\,dh/dt. The volume balance is

ATdhdt=Qin−Qout,A_T\frac{dh}{dt}=Q_{\rm in}-Q_{\rm out},

where the QQ's are volumetric flow rates. With AT=0.20 m2A_T=0.20\,\text{m}^2, Qin=0.010 m3/sQ_{\rm in}=0.010\,\text{m}^3/\text{s}, and Qout=0.006 m3/sQ_{\rm out}=0.006\,\text{m}^3/\text{s},

dhdt=0.010−0.0060.20=0.020 m/s.\frac{dh}{dt}=\frac{0.010-0.006}{0.20}=0.020\,\text{m/s}.

More enters than leaves, so the difference accumulates in the tank and the surface rises at 0.020 m/s0.020\,\text{m/s}. This relation assumes an incompressible liquid and a tank area that stays constant with height.

From Local Continuity to Pipe Flow

From local continuity to pipe flow

The control-volume balance describes conservation over a chosen region. The differential continuity equation expresses the same conservation locally:

∂ρ∂t+∇⋅(ρu)=0.\frac{\partial \rho}{\partial t}+\nabla\cdot(\rho\mathbf{u})=0.

Here, ρ\rho is density and u\mathbf{u} is velocity. The equation says that the local rate of density change plus the net outward transport of mass per unit volume is zero. For an incompressible fluid of constant density, it reduces to

∇⋅u=0.\nabla\cdot\mathbf{u}=0.

This condition does not mean the velocity must be steady: velocity can vary with time even while density stays constant.

Continuity through a pipe

Mass flow through a cross-section is described generally by

m˙=∫Aρ u⋅n dA.\dot m=\int_A \rho\,\mathbf{u}\cdot\mathbf{n}\,dA.

If flow is approximately uniform across the section and normal to it, this becomes m˙=ρAV\dot m=\rho AV, where AA is the area and VV is average speed. For steady flow through a pipe with one inlet, one outlet, and no leakage, the mass flow rates match:

ρ1A1V1=ρ2A2V2.\rho_1 A_1 V_1=\rho_2 A_2 V_2.

For an incompressible fluid, density is the same at both sections and cancels. Since is Q=AVQ=AV,

Q=A1V1=A2V2.Q=A_1V_1=A_2V_2.

Thus, for incompressible flow, reducing the area requires increasing the average speed to carry the same volume per unit time.

Worked contraction example. Water flows steadily from a wider section of area 6 cm26\,\text{cm}^2, where its average speed is 1.5 m/s1.5\,\text{m/s}, into a section of area 2 cm22\,\text{cm}^2. Using A1V1=A2V2A_1V_1=A_2V_2, solve for the unknown speed:

V2=V1A1A2=1.562=4.5 m/s.V_2=V_1\frac{A_1}{A_2} =1.5\frac{6}{2}=4.5\,\text{m/s}.

The smaller section carries the same volume per unit time at a higher speed.

For compressible steady flow, density may differ between sections. remains constant under the stated pipe assumptions, but need not. The inverse area–speed relation for constant QQ applies to incompressible flow, not generally to compressible flow.