Which sequence best describes a sound process for evaluating and selecting a pollution-control approach?
Evaluating Pollution-Control Options Online Quiz Questions
Use this free practice quiz with 20 questions to review Evaluating Pollution-Control Options, test your knowledge, and prepare for your next test or exam.
Which approaches should be included when considering pollution prevention and treatment options? Select all that apply.
- A
Source reduction
- B
Selecting only end-of-pipe treatment options
- C
Process changes
- D
Excluding reuse or recovery before screening options
- E
Reuse or recovery
- F
Considering only options already installed at the site
A pollution-control approach should be evaluated as a complete system rather than judged only by its removal-efficiency rating.
- A
True
- B
False
After selecting a pollution-control option, what procedures should be established to confirm that its performance continues?
When comparing pollution controls as complete systems, consider their reliability, residuals, , and .
Describe a staged process for evaluating and selecting a pollution-control approach, including how to account for prevention, feasibility, tradeoffs, costs, and continued performance.
A facility is comparing a fabric filter and a wet scrubber for particulate control. Which evaluation best supports a sound choice?
- A
Compare only the removal-efficiency ratings and choose the higher one.
- B
Choose the system with the lowest initial cost, without considering its residuals.
- C
Assess performance under actual exhaust conditions, energy and water needs, maintenance, and residuals, alongside applicable limits, site conditions, total costs, and permit conditions.
- D
Assume the same control system is preferable at every facility, regardless of its permit or site.
Which costs should be included in a life-cycle cost estimate for a pollution-control option? Select all that apply.
- A
Capital costs
- B
A removal-efficiency rating counted as a cost
- C
Operating costs
- D
Maintenance costs
- E
The facility's unrelated marketing expenses
- F
Monitoring and residuals costs
The best pollution-control system can be chosen from a single performance figure, without considering permit conditions, site conditions, or total costs.
- A
True
- B
False
What type of cost estimate should use consistent assumptions and include capital, operating, maintenance, monitoring, and residuals costs?
Complete the evaluation sequence: First identify . Next screen options for . After choosing an option, establish to confirm that its performance continues.
Which set of options should be considered when evaluating approaches to pollution control?
- A
Compare only end-of-pipe controls, since prevention is outside the evaluation.
- B
Consider source reduction, process changes, reuse or recovery, and end-of-pipe controls.
- C
Choose a control device first, then decide which pollutants it should address.
- D
Exclude reuse and recovery because they are not pollution-control options.
A pollution-control system should be selected solely by comparing one performance figure, such as its removal efficiency.
- A
True
- B
False
What prevention option reduces pollution at its origin? Enter the two-word term.
Which approach provides an appropriate life-cycle cost estimate for a pollution-control option?
- A
Include only initial capital costs and exclude expenses after installation.
- B
Estimate each option using different assumptions so its individual costs are easier to calculate.
- C
Use consistent assumptions and include capital, operating, maintenance, monitoring, and residuals costs.
- D
Count operating costs but exclude monitoring and residuals management.
After selecting a pollution-control option, establishing monitoring and maintenance procedures helps confirm that its performance continues.
- A
True
- B
False
What type of costs should be estimated using consistent assumptions and include capital, operating, maintenance, monitoring, and residuals expenses? Enter the hyphenated term.
Which approach best describes the final choose-and-verify stage of a pollution-control evaluation?
- A
Choose an option that meets applicable requirements and performs reliably, then establish procedures to verify continuing performance.
- B
Choose the option with the highest removal-efficiency figure, without considering permit conditions.
- C
Choose the lowest-cost option, even if it does not meet the applicable requirements.
- D
Select a control and omit monitoring once it has initially been installed.
In a fabric-filter comparison, what residual from the filter should be considered? Enter the two-word term.
A facility is comparing a fabric filter with a wet scrubber for particulate control. Which comparison best reflects a complete evaluation of the two systems?
- A
Compare the systems using removal efficiency alone.
- B
Consider the fabric filter's collected dust but ignore wastewater or sludge from the scrubber.
- C
Assume the same performance and resource needs regardless of the facility's exhaust conditions.
- D
Assess expected emissions, performance under actual exhaust conditions, energy and water needs, maintenance, and residuals.
Related study packs and tools
1 Electrical Quantities and Ohm’s Law
Learn how charge, current, voltage, resistance, power, and energy are related in electric circuits, including how to apply Ohm’s law and interpret worked calculations.
01 Foundations of Materials Science
Review how processing, structure, properties, and performance connect, and how engineering materials are classified and selected.
1 Vectors for Engineering Mechanics
A medium-difficulty quiz on representing vectors, calculating their components and magnitudes, and applying vector operations in engineering mechanics.
02 Atomic Bonding and Crystal Structures
Learn how atomic bonding relates to crystal order, how unit cells and Miller indices describe crystals, and how common metal and ceramic structures differ.
3 The Engineering Design Process
Learn how engineers define a need, explore and select design concepts, build and test prototypes, and use evidence to improve a solution.
04 Mechanical Properties of Materials
A medium-difficulty quiz on how materials respond to stress, deformation, repeated loading, sustained loading, and flaws.
05 Phase Diagrams and Phase Transformations
Learn how phase diagrams describe equilibrium, how solidification and transformations form microstructures, and how heat treatment and cooling control material structure.
06 Metals and Alloys
Review how metal structure, alloy composition, processing, heat treatment, and application requirements shape the properties and uses of engineering metals.
06 Metals and Alloys
Learn how metal structure, composition, processing, and heat treatment shape material properties, and how to select an alloy for an engineering application.
7 Engineering Ethics and Responsibility
Learn how engineers apply professional duties, ethical codes, safety practices, and community considerations to responsible engineering decisions.
08 Polymers
Learn how polymer chain structure, molecular-weight distribution, thermal behavior, and processing methods determine the properties and uses of polymer materials.
10 Materials Selection and Design
A medium-difficulty quiz on applying materials-selection principles, evaluating candidates, and accounting for processing and service requirements.