Timedora

Planar Structures: Reactions and Internal Forces

A lesson on modeling planar supports, drawing free-body diagrams, solving equilibrium equations, and finding internal forces in a member.

Model supports and draw the

Let prevented motion determine the reactions

A represents the action of a support on the body being analyzed. In a planar model, identify which motions the support prevents, then include a corresponding unknown reaction for each prevented motion:

Idealized planar supports and reactions
Idealized supportMotion preventedReactions to show
Roller or smooth surfaceMotion normal to the surfaceOne force normal to the surface
Pin or hingeHorizontal and vertical translationTwo force components, usually horizontal and vertical
Fixed connectionTranslation and rotationTwo force components and a reaction moment
Reactions for idealized supports in a planar model.

A roller does not resist motion along its surface, and a pin does not resist rotation. A fixed connection can resist rotation, so its diagram includes a moment as well as two force components. These are idealizations: the actual behavior depends on how the connection is built.

Build the

To prepare an FBD, first choose and isolate the body—or the part of a structure—you intend to analyze. Replace every support or connection removed from that body with its appropriate reaction components. Then show all applied forces and couples, including where they act and which way they point. Add relevant dimensions and coordinate axes so that positions and force directions are clear.

Include the loads acting on the isolated body. Do not include forces that the isolated body exerts on something outside the diagram: those belong to the other body’s FBD. This boundary matters because equilibrium equations must describe one clearly isolated body and all the external actions on it.

If a reaction’s direction is unknown, assume a direction and draw its arrow. A negative value from the later calculation means the actual direction is opposite to the assumed arrow; it does not mean the setup was invalid. Correctly identifying the body and representing its supports and loads are essential to obtaining valid equilibrium equations.

Use equilibrium to find support reactions

The three equations

For a rigid body at rest in a plane, the horizontal forces, vertical forces, and moments must each balance:

∑Fx=0,∑Fy=0,∑MO=0.\sum F_x=0,\qquad \sum F_y=0,\qquad \sum M_O=0.

The moment equation may be taken about any point OO. Choose one sign convention and keep it throughout the calculation—for example, rightward and upward forces positive, and counterclockwise moments positive. Taking moments about a point where unknown forces act can simplify the work: those forces have zero moment arm about that point and therefore make no contribution to that moment equation.

Worked example: reactions on a simply supported beam

A 6 m beam has a pin at AA, a roller at BB, and a 12 kN downward point load 2 m from AA. Find the support reactions. The pin supplies two components, AxA_x and AyA_y; the roller supplies a vertical reaction, ByB_y.

There is no horizontal applied load, so horizontal equilibrium gives

∑Fx=0:Ax=0.\sum F_x=0:\qquad A_x=0.

Take moments about AA, using counterclockwise moments as positive. The reaction AyA_y passes through AA, so it contributes no moment about that point. The roller reaction acts 6 m from AA, and the downward load acts 2 m from AA:

∑MA=0:(6 m)By−(12 kN)(2 m)=0.\sum M_A=0:\qquad (6\,\text{m})B_y-(12\,\text{kN})(2\,\text{m})=0.

Thus By=4 kNB_y=4\,\text{kN}. Now balance vertical forces:

∑Fy=0:Ay+By−12 kN=0,\sum F_y=0:\qquad A_y+B_y-12\,\text{kN}=0,

so Ay=8 kNA_y=8\,\text{kN}. The positive vertical reactions together equal the 12 kN downward load, while their moments about AA balance the load’s moment.

Check that each equation uses consistent signs and units, and that the results balance the whole structure. Equilibrium determines the unknowns only when there are enough independent equilibrium equations. If there are not, the structure may be statically indeterminate, and equilibrium alone cannot determine every reaction or internal force.

Cut a member to find

Expose the with a cut

Support reactions describe how a structure interacts with its surroundings. describe how the two parts of a member interact across a section. To find them at a particular location, imagine cutting through the member there and isolate one side. Represent the actions exposed at the cut, include all loads on the isolated segment, and apply equilibrium to that segment.

For a planar beam, the cut actions are:

  • Axial force NN: acts along the member and tends to stretch or shorten it.

  • Shear force VV: acts transverse to the member and tends to slide one part past the other.

  • Bending moment MM: tends to rotate one part relative to the other.

The assumed directions for shear and moment depend on the sign convention being used. Put those directions on the cut FBD and use them consistently. The actions on opposite sides of the same cut are equal in magnitude and opposite in direction.

Worked example: a cut 4 m from A

Use the beam from the previous example, with reactions Ay=8 kNA_y=8\,\text{kN} and a 12 kN downward load 2 m from AA. Cut the beam 4 m from AA and isolate its left segment. This segment contains the upward reaction at AA and the downward load; there is no horizontal load. Therefore, horizontal equilibrium gives N=0N=0.

Assume the cut shear acts upward on the isolated left segment. Vertical equilibrium gives

∑Fy=0:8−12+V=0,\sum F_y=0:\qquad 8-12+V=0,

so V=4 kNV=4\,\text{kN} in the assumed direction. For moments about the cut, take counterclockwise as positive. The 8 kN reaction is 4 m to the left of the cut, and the 12 kN load is 2 m to its left:

∑Mcut=0:−(8)(4)+(12)(2)+M=0.\sum M_{\text{cut}}=0:\qquad -(8)(4)+(12)(2)+M=0.

Solving gives M=8 kN⋅mM=8\,\text{kN}\cdot\text{m} in the assumed sense. These values apply to this cut location, not automatically to every point on the beam. can change along a member, especially at applied loads or supports.