Structural Elements, Forces, and Load Paths
A guided introduction to how structural members resist forces and how complete systems carry gravity and lateral loads to the ground.
Load Paths, Beams, and Columns
Following a
A structure does not support a load at just one point: connected elements pass forces onward until they reach supports and foundations. That continuous route is the . Gravity loads—such as a building’s weight, occupants, and stored materials—generally travel downward. Wind and earthquake forces act laterally, so floors or roofs transfer them to vertical elements that resist sideways movement and carry them toward the ground.
The exact behavior of an element depends on its shape and material, how it is supported and connected, and the loads applied to it. The diagram shows typical routes, not a claim that every structure uses the same components.
Beams: bending and shear
Beams are usually horizontal members that carry loads applied across their length and pass them to supports such as columns or walls. They resist these loads mainly through bending and shear. A shelf supported at both ends illustrates the idea: weight placed on it makes the shelf bend, and the shelf transfers the load to its end supports. A projecting from a support at only one end is called a cantilever.
Columns: compression and buckling
Columns generally carry loads mainly along their length in compression, transferring loads from beams or floors toward the foundation. A slender may buckle—bend sideways and lose stability—before its material is crushed. This is why length, cross-section, and bracing matter, not just the amount of compression. In short, a ’s primary response to transverse loading differs from a ’s primary role of carrying compression, though the behavior of either depends on its full structural context.
| Load type | Typical route |
|---|---|
| Gravity | Slab or floor load → beam → column or load-bearing wall → foundation |
| Lateral | Floor or roof force → shear wall, braced frame, or moment frame → foundation |
Trusses and Frames
Trusses: triangular geometry and axial forces
A is made of straight members connected in triangular patterns. Triangles help the assembly maintain its shape. In an idealized , members carry loads mainly as axial tension or compression—that is, forces along the members—rather than through bending. This arrangement can span a distance while leaving open spaces between members, as in a bridge. The idealization has limits: real joints and member connections may also produce bending.
Frames: two ways to resist sideways movement
Frames combine beams and columns, often in rectangular arrangements, to support floors and roofs. A adds diagonal members that resist sideways movement, primarily through tension and compression in the braces. A instead relies on -to- connections that resist rotation, allowing the connected members to help resist lateral forces through bending and shear. Either approach can provide open interior space, but performance depends strongly on connection stiffness and detailing.
| Frame type | How it resists sideways movement | Primary action described |
|---|---|---|
| Braced frame | Diagonal members | Tension and compression in braces |
| Moment frame | Beam-to-column connections resist rotation | Bending and shear in connected members |
Arches, Cables, and Walls
Different forms, different force demands
An is curved and carries loads mainly through compression, redirecting them toward its supports. Those supports generally must resist outward horizontal thrust as well as vertical force. An can span an opening efficiently when its geometry and supports suit the applied loads; loads that differ greatly from those anticipated can introduce bending.
A works differently: it is flexible and carries tension, but cannot resist compression or bending. It changes shape to align with the applied forces, forming a curve under load. In a suspension bridge, hangers carry the deck’s load to the main cables; the cables pass forces to towers and anchorages. The towers carry compression, while the anchorages resist the pull.
Walls: gravity, lateral forces, or both
Walls may be partitions, structural supports, or both. Load-bearing walls carry vertical loads from floors or roofs. Shear walls resist lateral forces from wind or earthquakes, typically through a combination of shear, bending, and axial action, and transfer those forces toward the foundation. These are roles, not necessarily separate wall types: a wall may carry gravity loads and also resist lateral forces.
| Element or role | Primary force role | Support or transfer point |
|---|---|---|
| Arch | Mainly compression | Supports resist outward horizontal thrust and vertical force |
| Cable | Tension; cannot resist compression or bending | Forces pass to towers and anchorages |
| Load-bearing wall | Carries vertical loads | Transfers floor or roof loads onward |
| Shear wall | Resists lateral forces through shear, bending, and axial action | Transfers forces toward the foundation |
Structural Systems at Work
Trace the force all the way to its support
A building commonly combines element types into continuous paths. For gravity loading, a typical route is slab → beams → columns or load-bearing walls → foundations. The slab’s load reaches the beams, which pass it to vertical supports; those supports carry it onward toward the foundations.
Lateral forces follow a different but connected route. Floors and roofs transfer wind or earthquake forces to shear walls, braced frames, or moment frames, which carry them down toward the foundations. The resisting elements and their connections must work as a system: if a connection cannot transfer the required force, the intended route is not complete.
A bridge provides another example of elements working together. Its deck may act with beams or trusses, while cables or arches carry forces to towers, abutments, and foundations. The central check in either kind of structure is to follow the force from where it is applied through connected components until it reaches a support. A component cannot do its job reliably unless the complete reaches the supports.
: A connected set of structural elements that carries loads continuously to the ground or other supports.