Which procedure is the most reliable way to solve a control-volume balance problem?
Control-Volume Mass and Energy Balances Online Quiz Questions
Use this free practice quiz with 20 questions to review Control-Volume Mass and Energy Balances, test your knowledge, and prepare for your next test or exam.
Select all statements that correctly describe mass and energy balances for a heat exchanger.
- A
At steady state, mass is conserved separately for each fluid stream.
- B
For an exchanger insulated from its surroundings, with no shaft work and negligible kinetic- and potential-energy changes, energy lost by the hot stream equals energy gained by the cold stream.
- C
The hot stream's energy loss always equals the cold stream's energy gain, even when heat escapes to the surroundings.
- D
If heat escapes to the surroundings, include that heat transfer in the balance rather than assuming the two streams exchange all the energy with each other.
- E
At steady state, the total mass flow rate through both streams combined must be zero.
True or false: In the control-volume energy balance sign convention used here, heat transfer is positive out of the control volume and work transfer is positive into it.
- A
True
- B
False
For an adiabatic nozzle with no shaft work and negligible elevation change, the example assumes a small inlet speed and an enthalpy decrease of 20 kJ/kg. What approximate outlet speed does the example report? Enter the numerical value in m/s.
For a control volume, the rate of mass accumulation equals total mass minus total mass . At steady state, there is no mass accumulation.
For a turbine and a compressor operating at steady state, state the simplified shaft-work relation for each when the device is adiabatic and changes in kinetic and potential energy are negligible. Explain how the enthalpy change relates to the work, and clarify the sign of work input under the convention that work is positive out of the control volume.
Which statement correctly applies the practical method for solving a control-volume balance problem?
- A
At steady state, total mass inflow may differ from total mass outflow if the energy balance is satisfied.
- B
Terms in the general energy balance can be omitted whenever they are expected to be small, even if the assumptions have not been checked.
- C
At steady state, total inlet and outlet mass flow rates must match, and energy-balance terms should be omitted only when their neglect is justified.
- D
The direction of heat and work transfer does not depend on the selected sign convention.
Select all statements that correctly describe the control-volume energy balance and its use.
- A
Using heat positive into and work positive out, the energy rate balance includes heat input minus work output, plus energy carried in by mass flow and minus energy carried out by mass flow.
- B
The energy carried by each unit of flowing mass is internal energy alone; flow work is not included.
- C
At steady flow with one inlet and one outlet, the energy balance includes the changes in enthalpy, kinetic energy, and potential energy between the inlet and outlet.
- D
When dividing the one-inlet, one-outlet steady-flow energy balance by mass flow rate, the heat and work terms per unit mass are q=Q˙/m˙ and w=W˙/m˙.
- E
Enthalpy in kJ/kg and velocity-squared terms in J/kg can be added directly without unit conversion.
True or false: For a steady, adiabatic turbine with negligible changes in kinetic and potential energy, the shaft power output is W˙out=m˙(h1−h2), so a positive enthalpy drop supplies shaft work.
- A
True
- B
False
A uniform flow has density 1.2 kg/m3, average velocity normal to the area of 5 m/s, and flow area 0.20 m2. What is its mass flow rate? Enter the numerical value in kg/s.
For an adiabatic nozzle with no shaft work and negligible elevation change, a decrease in fluid becomes an increase in kinetic energy.
A heat exchanger is insulated from its surroundings, has no shaft work, and has negligible kinetic- and potential-energy changes. Which statement describes the energy balance between the hot and cold streams?
- A
Energy lost by the hot stream equals energy gained by the cold stream.
- B
The hot stream's mass flow rate must equal the cold stream's mass flow rate.
- C
Energy lost by the hot stream must equal the heat transferred from the exchanger to its surroundings.
- D
The cold stream's enthalpy must remain unchanged.
True or false: For an adiabatic nozzle with no shaft work and negligible elevation change, the steady-flow energy balance is h1+2V12=h2+2V22.
- A
True
- B
False
A heat exchanger is insulated from its surroundings, has no shaft work, and has negligible kinetic- and potential-energy changes. Each stream has one inlet and one outlet. Which equation expresses the energy balance between the streams?
- A
m˙h(hh,in−hh,out)=m˙c(hc,out−hc,in)
- B
m˙h(hh,out−hh,in)=m˙c(hc,out−hc,in)
- C
m˙h=m˙c and hh,in−hh,out=hc,out−hc,in
- D
m˙h(hh,in−hh,out)=m˙c(hc,in−hc,out)
In the mass-flow terms of a control-volume energy balance, what thermodynamic property includes both internal energy and the flow work needed to push fluid across the control surface?
Which equation gives the rate of mass accumulation in a control volume?
- A
dtdmCV=∑inm˙−∑outm˙
- B
dtdmCV=∑outm˙−∑inm˙
- C
dtdmCV=∑inm˙+∑outm˙
- D
dtdmCV=0 for every control volume, whether or not it is at steady state
An adiabatic turbine operates at steady state with negligible changes in kinetic and potential energy. Steam flows at 0.20 kg/s, and its enthalpy drops by 300 kJ/kg. What is the idealized shaft power output?
For uniform flow through an area, which equation calculates the mass flow rate, with velocity taken normal to the area?
- A
m˙=ρVA, where V is the average velocity normal to the area
- B
m˙=AρV, where V is the average velocity normal to the area
- C
m˙=ρA, regardless of the fluid velocity
- D
m˙=ρVA, where V is the average velocity normal to the area
An adiabatic nozzle has no shaft work and negligible elevation change. The inlet speed is small, and the fluid’s enthalpy decreases by 20 kJ/kg. What is the approximate outlet speed?
- A
The outlet speed is approximately 100 m/s.
- B
The outlet speed is approximately 200 m/s.
- C
The outlet speed is approximately 400 m/s.
- D
The outlet speed is approximately 20 m/s.
A heat exchanger is insulated from its surroundings, has no shaft work, and has negligible kinetic- and potential-energy changes. Which statement describes its steady-flow energy balance?
- A
The hot and cold streams must have equal mass flow rates.
- B
The hot stream’s outlet enthalpy must equal the cold stream’s inlet enthalpy.
- C
The energy lost by the hot stream equals the energy gained by the cold stream.
- D
The energy lost by the hot stream must equal heat escaping to the surroundings.
Related study packs and tools
- Study guide
1 Electrical Quantities and Ohm’s Law
Learn how charge, current, voltage, resistance, power, and energy are related in electric circuits, including how to apply Ohm’s law and interpret worked calculations.
- Flashcards
01 Foundations of Materials Science
Review how processing, structure, properties, and performance connect, and how engineering materials are classified and selected.
- Quiz
1 Vectors for Engineering Mechanics
A medium-difficulty quiz on representing vectors, calculating their components and magnitudes, and applying vector operations in engineering mechanics.
- Flashcards
04 Mechanical Properties of Materials
Review how materials respond to forces and deformation, and how strength, fracture, fatigue, creep, and hardness are assessed.
- Quiz
04 Mechanical Properties of Materials
A medium-difficulty quiz on how materials respond to stress, deformation, repeated loading, sustained loading, and flaws.
- Study guide
5 Thermodynamic Cycles and Devices
Learn how thermodynamic cycles transfer energy, how engines and reversed-cycle devices perform, and how the vapor-compression cycle moves heat.
- Flashcards
06 Metals and Alloys
Review how metal structure, alloy composition, processing, heat treatment, and application requirements shape the properties and uses of engineering metals.
- Study guide
06 Metals and Alloys
Learn how metal structure, composition, processing, and heat treatment shape material properties, and how to select an alloy for an engineering application.
- Study guide
7 Engineering Ethics and Responsibility
Learn how engineers apply professional duties, ethical codes, safety practices, and community considerations to responsible engineering decisions.
- Study guide
08 Polymers
Learn how polymer chain structure, molecular-weight distribution, thermal behavior, and processing methods determine the properties and uses of polymer materials.
- Study guide
09 Composite Materials
Learn how composite materials combine constituents, how reinforcement arrangements shape their properties, and how to select them for particular applications.
- Quiz
10 Materials Selection and Design
A medium-difficulty quiz on applying materials-selection principles, evaluating candidates, and accounting for processing and service requirements.