Timedora

Control-Volume Mass and Energy Balances

A practical lesson on conserving mass and energy in control volumes, applying balances to common flow devices, and checking assumptions and units.

Define the and Write Its Balances

Choose a

An open system, or (CV), is a selected region through which mass can flow. Its boundary is called the control surface. Turbines, compressors, nozzles, and heat exchangers can all be analyzed this way. Unlike a closed system, a can gain or lose both mass and energy through its boundary.

The choice of boundary is part of setting up the problem: draw it around the device or region you want to analyze, then identify every stream and every heat or work interaction that crosses it.

Begin with mass conservation

The mass balance says that the rate of mass accumulating inside the equals the total rate entering minus the total rate leaving:

dmCVdt=∑inm˙−∑outm˙.\frac{dm_{CV}}{dt}=\sum_{in}\dot m-\sum_{out}\dot m.

Here, m˙\dot m is mass flow rate. At , mass inside the does not accumulate, so the balance simplifies to

∑inm˙=∑outm˙.\sum_{in}\dot m=\sum_{out}\dot m.

With one inlet and one outlet, this means m˙1=m˙2\dot m_1=\dot m_2. For uniform flow through an area, the rate can also be calculated from m˙=ρVA\dot m=\rho V A, where ρ\rho is density, VV is the average velocity normal to the area, and AA is the area. This relation connects the flow rate crossing a surface to the fluid’s density and motion.

Write the energy balance with a consistent sign convention

Take Q˙\dot Q as positive into the and work transfer W˙\dot W as positive out of it. With that convention, the general energy rate balance is

dECVdt=Q˙−W˙+∑inm˙(h+V22+gz)−∑outm˙(h+V22+gz).\frac{dE_{CV}}{dt}=\dot Q-\dot W +\sum_{in}\dot m\left(h+\frac{V^2}{2}+gz\right) -\sum_{out}\dot m\left(h+\frac{V^2}{2}+gz\right).

The energy stored in the changes through heat and work interactions and through energy carried across the boundary by incoming and outgoing mass. Each mass-flow term includes specific hh, specific kinetic energy V2/2V^2/2, and specific potential energy gzgz.

appears rather than internal energy alone because h=u+pvh=u+pv: it includes internal energy uu and the flow work pvpv needed to push fluid across the control surface. Leaving out that flow-work contribution would not fully account for energy transported by the flowing fluid.

At steady flow, stored energy does not change. For one inlet and one outlet, the balance becomes

Q˙−W˙=m˙[(h2−h1)+V22−V122+g(z2−z1)].\dot Q-\dot W=\dot m\left[(h_2-h_1)+\frac{V_2^2-V_1^2}{2}+g(z_2-z_1)\right].

Dividing by m˙\dot m gives the balance per unit mass, with q=Q˙/m˙q=\dot Q/\dot m and w=W˙/m˙w=\dot W/\dot m. Keep units consistent: is often reported in kJ/kg\mathrm{kJ/kg}, whereas velocity-squared terms in SI units are in J/kg\mathrm{J/kg}. Convert one to match the other before combining terms.

Work-Producing, Work-Consuming, and Accelerating Devices

Simplify only after stating the assumptions

The device relationships below come from the steady-flow energy balance. In each case, the simplified equation relies on assumptions about , shaft work, and changes in kinetic or potential energy. Identify those assumptions before dropping terms.

Turbines: decrease supplies work

For a operating steadily, adiabatically, and with negligible changes in kinetic and potential energy, the work produced is

W˙out=m˙(h1−h2).\dot W_{out}=\dot m(h_1-h_2).

Thus, when the fluid’s falls from inlet state 1 to outlet state 2, that decrease supplies shaft power. For the source example, steam flows at 0.20 kg/s0.20\ \mathrm{kg/s} and its drops by 300 kJ/kg300\ \mathrm{kJ/kg}. The power is

W˙out=(0.20 kg/s)(300 kJ/kg)=60 kJ/s=60 kW.\dot W_{out}=(0.20\ \mathrm{kg/s})(300\ \mathrm{kJ/kg}) =60\ \mathrm{kJ/s}=60\ \mathrm{kW}.

The units confirm the interpretation: mass flow rate times energy per unit mass gives energy per unit time, or power.

Compressors: work input raises

A requires shaft work to raise a gas’s pressure. For steady, adiabatic operation with negligible kinetic- and potential-energy changes, the positive magnitude of the required work input is

W˙in=m˙(h2−h1).\dot W_{in}=\dot m(h_2-h_1).

The usually rises across the , so h2−h1h_2-h_1 is positive in this relation. Be careful not to confuse the positive magnitude W˙in\dot W_{in} with the signed work transfer in the general balance: with work positive out of the , work input means W˙<0\dot W<0.

Nozzles: decrease raises velocity

A accelerates fluid. For an adiabatic with no shaft work and negligible elevation change, the energy balance reduces to

h1+V122=h2+V222.h_1+\frac{V_1^2}{2}=h_2+\frac{V_2^2}{2}.

The reduction in is matched by an increase in kinetic energy. In the source example, the inlet speed is small and falls by 20 kJ/kg20\ \mathrm{kJ/kg}. Treating the inlet kinetic energy as negligible, convert the drop to SI units and solve for the outlet speed:

V222≈20,000 J/kg,V2≈2(20,000 J/kg)=200 m/s.\frac{V_2^2}{2}\approx 20{,}000\ \mathrm{J/kg},\qquad V_2\approx\sqrt{2(20{,}000\ \mathrm{J/kg})}=200\ \mathrm{m/s}.

The conversion matters because V2/2V^2/2 in SI units is measured in J/kg\mathrm{J/kg}. The result is an approximate outlet speed under the stated assumptions, not a general result independent of operating conditions.

Heat Exchangers and a Reliable Solution Method

Balance the two streams separately

At , mass is conserved for each heat-exchanger stream separately. For one inlet and one outlet on each side, the hot stream’s inlet and outlet mass flow rates match, and the cold stream’s inlet and outlet mass flow rates match. The hot and cold mass flow rates do not have to equal each other.

If the exchanger is insulated from its surroundings, has no shaft work, and has negligible changes in kinetic and potential energy, the energy lost by the hot stream equals the energy gained by the cold stream:

m˙h(hh,in−hh,out)=m˙c(hc,out−hc,in).\dot m_h(h_{h,in}-h_{h,out}) =\dot m_c(h_{c,out}-h_{c,in}).

The differences are written in the direction of energy transfer: the hot stream’s inlet exceeds its outlet , while the cold stream’s outlet exceeds its inlet . This equation is a simplified balance for the two streams under the assumptions just stated.

If heat escapes to the surroundings, the streams do not exchange all the energy with each other. Include that in the control-volume energy balance rather than using the equality above as though the exchanger were insulated.

A reliable order for solving control-volume problems

  1. Define the boundary. Draw and label the . Mark every inlet, outlet, , and work interaction that crosses it.

  2. Choose signs and collect known information. Use one consistent sign convention—for example, heat positive in and work positive out—and list known states and mass flow rates.

  3. Check mass conservation. Write the mass balance first. At steady flow, the total inlet mass flow rate must equal the total outlet mass flow rate. For a , apply this check to each stream separately.

  4. Write the general energy balance. Include energy carried by mass, heat, and work before simplifying.

  5. Justify every omitted term. For example, an adiabatic assumption supports setting to zero; negligible elevation or velocity changes support omitting the corresponding potential- or kinetic-energy terms. Do not drop a term merely because it is inconvenient.

  6. Find properties and verify the result. Use property data or appropriate relations to obtain enthalpies. Check that units are compatible and that the signs and directions of heat and work match the physical situation.

This sequence keeps the balance tied to the actual boundary and assumptions. It also helps distinguish a physical transfer direction from a sign-convention choice: the convention determines the algebraic sign, while the boundary and device behavior determine what is entering or leaving.