Groundwater, Seepage, and Effective Stress
A lesson on how groundwater moves through soil, changes the stress carried by soil particles, and affects ground stability.
Soil Pores, Water, and Saturation
Soil Pores, Water, and Saturation
Soil consists of solid particles and the spaces between them, called voids. Those voids can contain water, air, or a mixture of both. Below the , soil is generally treated as saturated because its interconnected voids are filled with water. Above it, soil is often partially saturated.
The is not always a sharp boundary between wet and dry ground. Water can rise above it through small pores by capillary action. In a confined layer, water observed in a piezometer may rise to a piezometric level higher than the layer itself.
Two properties of soil pores are easy to confuse. describes how much void space the soil contains. describes how readily fluid can pass through connected voids. A soil can have substantial yet low if its pores are small or poorly connected. In geotechnical calculations, water-transmitting capacity is commonly represented by hydraulic conductivity, K or k; it depends on both the soil and the fluid.
and Groundwater Flow
and Groundwater Flow
Groundwater moves in response to differences in , the water’s energy per unit weight. It flows from higher total head toward lower total head; the direction is not necessarily straight downward. For ordinary groundwater flow, velocity head is negligible, so total head is approximately the sum of elevation head and pressure head.
For laminar flow through saturated soil, relates discharge to the soil’s hydraulic conductivity, the flow area, and the hydraulic gradient:
Here, Q is discharge (volume per time), K is hydraulic conductivity, A is the cross-sectional area normal to flow, and i is the difference in head, Δh, over the flow length L. The equation shows that, for the same area, a greater conductivity or gradient produces greater discharge.
Worked example. Suppose K = 1 × 10⁻⁵ m/s, i = 0.2, and A = 2 m². Substituting into :
Thus, the discharge through the stated area is 4 × 10⁻⁶ m³/s.
Dividing discharge by total area gives , or specific discharge:
This is not the actual average speed of water moving through the pore spaces: the total area includes both solids and voids. The approximate pore-water speed is , where is effective . Conductivity also varies with grain size, soil structure, layering, and water conditions; layered ground can therefore have strongly directional flow.
Seepage, Stability, and
Seepage, Stability, and
Seeping water exerts forces on soil grains, and the direction of seepage matters. Downward seepage tends to increase the stress carried by the soil skeleton, while upward seepage tends to reduce it. If upward flow becomes sufficiently strong, can be lost and the soil may become unstable, a condition often called quick or boiling soil. Upward seepage and high groundwater flow can threaten excavations and slope stability.
For an ideal saturated cohesionless soil, the critical upward gradient is approximately
Here, γ′ is , γw is the unit weight of water, Gs is the specific gravity of the soil solids, and e is void ratio. This relation indicates when instability may become a concern in the idealized case. It is a warning indicator, not a substitute for evaluating actual site conditions.
in saturated soil
For saturated soil, is the part of total stress carried through contacts between soil particles. It is calculated as
where σ is total stress and u is pore-water pressure. Water pressure acts in all directions, but it does not provide the soil skeleton’s frictional resistance. Changes in therefore govern much of saturated soil’s strength and compression behavior.
Worked example. Consider 2 m of moist ground above the , with unit weight γ = 18 kN/m³, and 3 m of saturated soil below it, with γsat = 20 kN/m³. At 5 m depth, total vertical stress is the weight per unit area of both layers:
The point lies 3 m below the , so its pore-water pressure is approximately
Subtracting pore pressure from total stress gives
So approximately 66.6 kPa is carried through the soil-particle contacts. Below the , this increases approximately at the , γ′ = γsat − γw.
Groundwater and loading changes can alter pore pressure and . Lowering the generally increases in the newly drained zone, which can contribute to ground compression and settlement. Rapid loading of saturated, low- soil may initially increase pore-water pressure; and deformation then change as that excess pressure dissipates.
Capillarity and Unsaturated Soil
Capillarity and Unsaturated Soil
Surface tension draws water into small soil pores, allowing it to rise above the and form a . Soil in this zone may be saturated or nearly saturated. Its pore-water pressure is below atmospheric pressure (negative gauge pressure), a condition often described as . Finer pores can sustain greater capillary rise than larger pores, though the exact height and moisture distribution depend on soil and drainage conditions.
Capillary suction can temporarily increase apparent soil strength or stiffness, but that effect may change when the ground wets or dries. The saturated-soil equation is not a complete model for partially saturated ground: air and water coexist in its pores, so additional concepts are needed to describe its behavior.
: The upward hydraulic gradient at which an ideal saturated cohesionless soil may lose and become unstable.